About software updates

Fixed a bug where the measurements for the DXF-exported graphics were indicated in inches
Fixed a bug where the image and result frame shown on the screen sometimes do not immediately correspond to each other when the result of positioning search is displayed on the IM-6145
Fixed a bug where a value greater than -1° but less than 0° could not be correctly output when the angle display format was in a sexagesimal system and a value for CSV output was in the fixed-length format

Error where "确定" was shown instead of "OK" on the preview display during multiple batch measurements on the simplified Chinese edition corrected

Function for switching the language added (Japanese/English/German/French/Italian/simplified Chinese/traditional Chinese)
CP and CPK calculations for geometric dimension and tolerance changed

X stage position changed to the center when making a new normal measurement on the IM-6120/6125/6225/6225T
Function added for changing the X stage position when editing the measurement settings data of a normal measurement
Function added for aligning the display orientation of the measurement result with the reference element on the preview display during IM-6225T height measurements
Deleting/editing data added to the items that are restricted by a password in the security settings
Function added that makes it possible to set the lot number, serial counter, and name as required input in multi measurement mode
Function for overlapping CAD data added
Folder path display changed to omit the drive name or the network address name

Error where the software would freeze during measurements using point elements (Point on line, Point on Arc, Corner Arc, and Chamfer) corrected
Error where it was impossible to change the IM-user password corrected
Error where the software would freeze after updating to IM-6000 version 4.0 or later corrected
Error where the software would sometimes be forced to exit when a layer that had been set with the Z stage position at the upper limit is present corrected
Error where the unit was not displayed with Display Difference Value for Pitch width of line, Pitch width of circular angle, and Area corrected
Error where a different item was set as the target and then not displayed on the [Batch tolerance settings] screen when [Final partial cumulative pitch deviation] was cleared as the judgment target during partial cumulative pitch deviation measurements corrected
Error where cumulative pitch deviation and partial cumulative pitch deviation were not sorted correctly when the "Display results in the descending order of errors" check box was selected has been corrected

Fixed a bug where errors in measurement results became larger (0.5 to less than 10 μm) when performing measurement in high-precision measurement mode using positioning search with the IM-6140/IM-6145 connected

Added display language switch function (Japanese/English/German/French/Spanish/Simplified Chinese/Traditional Chinese/Korean/Thai)

Fixed a bug where the shortcut menu was not displayed even when right-clicking the reference dialog box for the folder in the folder settings

Fixed a bug there the center line between non-parallel edges could not be extracted correctly when edge extraction parameter automatic adjustment was enabled for the center line of the element tool

IM-6125/IM-6145/IM-6225 support
Updated the adjustment contents of edge extraction parameter automatic adjustment
Added a multi-edge detection function to edge extraction parameter automatic adjustment
Added a function to prioritize continuous edge points for edge extraction parameters
Added a function to remove isolated points for edge extraction parameter
Changed the detection threshold value for inspection of sink marks and flash
Added Auto Measurement Mode
Added automatic measurement elements for the application tool
Added the CSV automatic saving format setting function
Added the one-side tolerance setting function for the contour profile elements
Added the contour line emphasis display function
Changed the pattern search default setting to "Accuracy priority"
Added a display/hide switch function to the units for length
Added a display/hide switch function to the serial number
Added batch restriction for options, folder settings, CSV saving destination setting to the restriction items in the security settings
Added the Q-DAS output setting function
Added a function to confirm results before output for the multi measurement mode
Added account and password settings to the folder setting function

Fixed a bug where the thread tolerance table was not referable in languages that use a comma as a decimal point
Fixed a bug where the German help window for the base coordinates was displayed in English
Fixed a bug where the next-day statistical data was not extracted when the date was changed during measurement and data saving
Fixed a bug where the φ symbol was displayed in the roundness preview
Fixed a bug where measurement execution could fail in measurement setting mode when the tolerance for the contour profile was reduced using CAD import